commit | author | age
|
fdb514
|
1 |
## Dovecot configuration file |
T |
2 |
|
|
3 |
# If you're in a hurry, see http://wiki.dovecot.org/QuickConfiguration |
|
4 |
|
|
5 |
# "dovecot -n" command gives a clean output of the changed settings. Use it |
|
6 |
# instead of copy&pasting this file when posting to the Dovecot mailing list. |
|
7 |
|
|
8 |
# '#' character and everything after it is treated as comments. Extra spaces |
|
9 |
# and tabs are ignored. If you want to use either of these explicitly, put the |
|
10 |
# value inside quotes, eg.: key = "# char and trailing whitespace " |
|
11 |
|
|
12 |
# Default values are shown for each setting, it's not required to uncomment |
|
13 |
# those. These are exceptions to this though: No sections (e.g. namespace {}) |
|
14 |
# or plugin settings are added by default, they're listed only as examples. |
|
15 |
# Paths are also just examples with the real defaults being based on configure |
|
16 |
# options. The paths listed here are for configure --prefix=/usr |
|
17 |
# --sysconfdir=/etc --localstatedir=/var --with-ssldir=/etc/ssl |
|
18 |
|
|
19 |
# Base directory where to store runtime data. |
|
20 |
#base_dir = /var/run/dovecot/ |
|
21 |
|
|
22 |
# Protocols we want to be serving: imap imaps pop3 pop3s managesieve |
|
23 |
# If you only want to use dovecot-auth, you can set this to "none". |
|
24 |
#protocols = imap imaps |
|
25 |
protocols = imap imaps pop3 pop3s |
|
26 |
|
|
27 |
# A space separated list of IP or host addresses where to listen in for |
|
28 |
# connections. "*" listens in all IPv4 interfaces. "[::]" listens in all IPv6 |
|
29 |
# interfaces. Use "*, [::]" for listening both IPv4 and IPv6. |
|
30 |
# |
|
31 |
# If you want to specify ports for each service, you will need to configure |
|
32 |
# these settings inside the protocol imap/pop3/managesieve { ... } section, |
|
33 |
# so you can specify different ports for IMAP/POP3/MANAGESIEVE. For example: |
|
34 |
# protocol imap { |
|
35 |
# listen = *:10143 |
|
36 |
# ssl_listen = *:10943 |
|
37 |
# .. |
|
38 |
# } |
|
39 |
# protocol pop3 { |
|
40 |
# listen = *:10100 |
|
41 |
# .. |
|
42 |
# } |
|
43 |
# protocol managesieve { |
|
44 |
# listen = *:12000 |
|
45 |
# .. |
|
46 |
# } |
|
47 |
#listen = * |
c2568b
|
48 |
listen = *,[::] |
fdb514
|
49 |
|
T |
50 |
# Disable LOGIN command and all other plaintext authentications unless |
|
51 |
# SSL/TLS is used (LOGINDISABLED capability). Note that if the remote IP |
|
52 |
# matches the local IP (ie. you're connecting from the same computer), the |
|
53 |
# connection is considered secure and plaintext authentication is allowed. |
|
54 |
#disable_plaintext_auth = yes |
|
55 |
disable_plaintext_auth = no |
|
56 |
|
|
57 |
# Should all IMAP and POP3 processes be killed when Dovecot master process |
|
58 |
# shuts down. Setting this to "no" means that Dovecot can be upgraded without |
|
59 |
# forcing existing client connections to close (although that could also be |
|
60 |
# a problem if the upgrade is eg. because of a security fix). This however |
|
61 |
# means that after master process has died, the client processes can't write |
|
62 |
# to log files anymore. |
|
63 |
#shutdown_clients = yes |
|
64 |
shutdown_clients = yes |
|
65 |
|
|
66 |
## |
|
67 |
## Logging |
|
68 |
## |
|
69 |
|
|
70 |
# Log file to use for error messages, instead of sending them to syslog. |
|
71 |
# /dev/stderr can be used to log into stderr. |
|
72 |
#log_path = |
|
73 |
|
|
74 |
# Log file to use for informational and debug messages. |
|
75 |
# Default is the same as log_path. |
|
76 |
#info_log_path = |
|
77 |
|
|
78 |
# Prefix for each line written to log file. % codes are in strftime(3) |
|
79 |
# format. |
|
80 |
#log_timestamp = "%b %d %H:%M:%S " |
|
81 |
log_timestamp = "%Y-%m-%d %H:%M:%S " |
|
82 |
|
|
83 |
# Syslog facility to use if you're logging to syslog. Usually if you don't |
|
84 |
# want to use "mail", you'll use local0..local7. Also other standard |
|
85 |
# facilities are supported. |
|
86 |
#syslog_facility = mail |
|
87 |
|
|
88 |
## |
|
89 |
## SSL settings |
|
90 |
## |
|
91 |
|
|
92 |
# IP or host address where to listen in for SSL connections. Remember to also |
|
93 |
# add imaps and/or pop3s to protocols setting. Defaults to same as "listen" |
|
94 |
# setting if not specified. |
|
95 |
#ssl_listen = |
|
96 |
|
|
97 |
# SSL/TLS support: yes, no, required. <doc/wiki/SSL.txt> |
6ed098
|
98 |
ssl = yes |
fdb514
|
99 |
|
T |
100 |
# PEM encoded X.509 SSL/TLS certificate and private key. They're opened before |
|
101 |
# dropping root privileges, so keep the key file unreadable by anyone but |
|
102 |
# root. Included doc/mkcert.sh can be used to easily generate self-signed |
|
103 |
# certificate, just make sure to update the domains in dovecot-openssl.cnf |
|
104 |
#ssl_cert_file = /etc/ssl/certs/dovecot.pem |
|
105 |
#ssl_key_file = /etc/ssl/private/dovecot.pem |
|
106 |
|
8cf78b
|
107 |
ssl_cert_file = /etc/postfix/smtpd.cert |
T |
108 |
ssl_key_file = /etc/postfix/smtpd.key |
|
109 |
|
fdb514
|
110 |
# If key file is password protected, give the password here. Alternatively |
T |
111 |
# give it when starting dovecot with -p parameter. Since this file is often |
|
112 |
# world-readable, you may want to place this setting instead to a different |
|
113 |
# root owned 0600 file by using !include_try <path>. |
|
114 |
#ssl_key_password = |
|
115 |
|
|
116 |
# File containing trusted SSL certificate authorities. Set this only if you |
|
117 |
# intend to use ssl_verify_client_cert=yes. The CAfile should contain the |
|
118 |
# CA-certificate(s) followed by the matching CRL(s). |
|
119 |
#ssl_ca_file = |
|
120 |
|
|
121 |
# Request client to send a certificate. If you also want to require it, set |
|
122 |
# ssl_require_client_cert=yes in auth section. |
|
123 |
#ssl_verify_client_cert = no |
|
124 |
|
|
125 |
# Which field from certificate to use for username. commonName and |
|
126 |
# x500UniqueIdentifier are the usual choices. You'll also need to set |
|
127 |
# ssl_username_from_cert=yes. |
|
128 |
#ssl_cert_username_field = commonName |
|
129 |
|
|
130 |
# How often to regenerate the SSL parameters file. Generation is quite CPU |
|
131 |
# intensive operation. The value is in hours, 0 disables regeneration |
|
132 |
# entirely. |
|
133 |
#ssl_parameters_regenerate = 168 |
|
134 |
|
|
135 |
# SSL ciphers to use |
|
136 |
#ssl_cipher_list = ALL:!LOW:!SSLv2 |
|
137 |
|
|
138 |
# Show protocol level SSL errors. |
|
139 |
#verbose_ssl = no |
|
140 |
|
|
141 |
## |
|
142 |
## Login processes |
|
143 |
## |
|
144 |
|
|
145 |
# <doc/wiki/LoginProcess.txt> |
|
146 |
|
|
147 |
# Directory where authentication process places authentication UNIX sockets |
|
148 |
# which login needs to be able to connect to. The sockets are created when |
|
149 |
# running as root, so you don't have to worry about permissions. Note that |
|
150 |
# everything in this directory is deleted when Dovecot is started. |
|
151 |
#login_dir = /var/run/dovecot/login |
|
152 |
|
|
153 |
# chroot login process to the login_dir. Only reason not to do this is if you |
|
154 |
# wish to run the whole Dovecot without roots. <doc/wiki/Rootless.txt> |
|
155 |
#login_chroot = yes |
|
156 |
|
|
157 |
# User to use for the login process. Create a completely new user for this, |
|
158 |
# and don't use it anywhere else. The user must also belong to a group where |
|
159 |
# only it has access, it's used to control access for authentication process. |
|
160 |
# Note that this user is NOT used to access mails. <doc/wiki/UserIds.txt> |
|
161 |
#login_user = dovecot |
|
162 |
|
|
163 |
# Set max. process size in megabytes. If you don't use |
|
164 |
# login_process_per_connection you might need to grow this. |
|
165 |
#login_process_size = 64 |
|
166 |
|
|
167 |
# Should each login be processed in it's own process (yes), or should one |
|
168 |
# login process be allowed to process multiple connections (no)? Yes is more |
|
169 |
# secure, espcially with SSL/TLS enabled. No is faster since there's no need |
|
170 |
# to create processes all the time. |
|
171 |
#login_process_per_connection = yes |
|
172 |
|
|
173 |
# Number of login processes to keep for listening new connections. |
|
174 |
#login_processes_count = 3 |
|
175 |
|
|
176 |
# Maximum number of login processes to create. The listening process count |
|
177 |
# usually stays at login_processes_count, but when multiple users start logging |
|
178 |
# in at the same time more extra processes are created. To prevent fork-bombing |
|
179 |
# we check only once in a second if new processes should be created - if all |
|
180 |
# of them are used at the time, we double their amount until the limit set by |
|
181 |
# this setting is reached. |
|
182 |
#login_max_processes_count = 128 |
|
183 |
|
|
184 |
# Maximum number of connections allowed per each login process. This setting |
|
185 |
# is used only if login_process_per_connection=no. Once the limit is reached, |
|
186 |
# the process notifies master so that it can create a new login process. |
|
187 |
#login_max_connections = 256 |
|
188 |
|
|
189 |
# Greeting message for clients. |
|
190 |
#login_greeting = Dovecot ready. |
|
191 |
|
|
192 |
# Space separated list of trusted network ranges. Connections from these |
|
193 |
# IPs are allowed to override their IP addresses and ports (for logging and |
|
194 |
# for authentication checks). disable_plaintext_auth is also ignored for |
|
195 |
# these networks. Typically you'd specify your IMAP proxy servers here. |
|
196 |
#login_trusted_networks = |
|
197 |
|
|
198 |
# Space-separated list of elements we want to log. The elements which have |
|
199 |
# a non-empty variable value are joined together to form a comma-separated |
|
200 |
# string. |
|
201 |
#login_log_format_elements = user=<%u> method=%m rip=%r lip=%l %c |
|
202 |
|
|
203 |
# Login log format. %$ contains login_log_format_elements string, %s contains |
|
204 |
# the data we want to log. |
|
205 |
#login_log_format = %$: %s |
|
206 |
|
|
207 |
## |
|
208 |
## Mailbox locations and namespaces |
|
209 |
## |
|
210 |
|
|
211 |
# Location for users' mailboxes. This is the same as the old default_mail_env |
|
212 |
# setting. The default is empty, which means that Dovecot tries to find the |
|
213 |
# mailboxes automatically. This won't work if the user doesn't have any mail |
|
214 |
# yet, so you should explicitly tell Dovecot the full location. |
|
215 |
# |
|
216 |
# If you're using mbox, giving a path to the INBOX file (eg. /var/mail/%u) |
|
217 |
# isn't enough. You'll also need to tell Dovecot where the other mailboxes are |
|
218 |
# kept. This is called the "root mail directory", and it must be the first |
|
219 |
# path given in the mail_location setting. |
|
220 |
# |
|
221 |
# There are a few special variables you can use, eg.: |
|
222 |
# |
|
223 |
# %u - username |
|
224 |
# %n - user part in user@domain, same as %u if there's no domain |
|
225 |
# %d - domain part in user@domain, empty if there's no domain |
|
226 |
# %h - home directory |
|
227 |
# |
|
228 |
# See <doc/wiki/Variables.txt> for full list. Some examples: |
|
229 |
# |
|
230 |
# mail_location = maildir:~/Maildir |
|
231 |
# mail_location = mbox:~/mail:INBOX=/var/mail/%u |
|
232 |
# mail_location = mbox:/var/mail/%d/%1n/%n:INDEX=/var/indexes/%d/%1n/%n |
|
233 |
# |
|
234 |
# <doc/wiki/MailLocation.txt> |
|
235 |
# |
|
236 |
#mail_location = |
|
237 |
mail_location = maildir:/var/vmail/%d/%n/Maildir |
|
238 |
|
|
239 |
# If you need to set multiple mailbox locations or want to change default |
|
240 |
# namespace settings, you can do it by defining namespace sections. |
|
241 |
# |
|
242 |
# You can have private, shared and public namespaces. Private namespaces |
|
243 |
# are for user's personal mails. Shared namespaces are for accessing other |
|
244 |
# users' mailboxes that have been shared. Public namespaces are for shared |
|
245 |
# mailboxes that are managed by sysadmin. If you create any shared or public |
|
246 |
# namespaces you'll typically want to enable ACL plugin also, otherwise all |
|
247 |
# users can access all the shared mailboxes, assuming they have permissions |
|
248 |
# on filesystem level to do so. |
|
249 |
# |
|
250 |
# REMEMBER: If you add any namespaces, the default namespace must be added |
|
251 |
# explicitly, ie. mail_location does nothing unless you have a namespace |
|
252 |
# without a location setting. Default namespace is simply done by having a |
|
253 |
# namespace with empty prefix. |
|
254 |
#namespace private { |
|
255 |
# Hierarchy separator to use. You should use the same separator for all |
|
256 |
# namespaces or some clients get confused. '/' is usually a good one. |
|
257 |
# The default however depends on the underlying mail storage format. |
|
258 |
#separator = |
|
259 |
|
|
260 |
# Prefix required to access this namespace. This needs to be different for |
|
261 |
# all namespaces. For example "Public/". |
|
262 |
#prefix = |
|
263 |
|
|
264 |
# Physical location of the mailbox. This is in same format as |
|
265 |
# mail_location, which is also the default for it. |
|
266 |
#location = |
|
267 |
|
|
268 |
# There can be only one INBOX, and this setting defines which namespace |
|
269 |
# has it. |
|
270 |
#inbox = no |
|
271 |
|
|
272 |
# If namespace is hidden, it's not advertised to clients via NAMESPACE |
|
273 |
# extension. You'll most likely also want to set list=no. This is mostly |
|
274 |
# useful when converting from another server with different namespaces which |
|
275 |
# you want to deprecate but still keep working. For example you can create |
|
276 |
# hidden namespaces with prefixes "~/mail/", "~%u/mail/" and "mail/". |
|
277 |
#hidden = yes |
|
278 |
|
|
279 |
# Show the mailboxes under this namespace with LIST command. This makes the |
|
280 |
# namespace visible for clients that don't support NAMESPACE extension. |
|
281 |
# "children" value lists child mailboxes, but hides the namespace prefix. |
|
282 |
#list = yes |
|
283 |
|
|
284 |
# Namespace handles its own subscriptions. If set to "no", the parent |
|
285 |
# namespace handles them (empty prefix should always have this as "yes") |
|
286 |
#subscriptions = yes |
|
287 |
#} |
|
288 |
|
|
289 |
# Example shared namespace configuration |
|
290 |
#namespace shared { |
|
291 |
#separator = / |
|
292 |
|
|
293 |
# Mailboxes are visible under "shared/user@domain/" |
|
294 |
# %%n, %%d and %%u are expanded to the destination user. |
|
295 |
#prefix = shared/%%u/ |
|
296 |
|
|
297 |
# Mail location for other users' mailboxes. Note that %variables and ~/ |
|
298 |
# expands to the logged in user's data. %%n, %%d, %%u and %%h expand to the |
|
299 |
# destination user's data. |
|
300 |
#location = maildir:%%h/Maildir:INDEX=~/Maildir/shared/%%u |
|
301 |
|
|
302 |
# Use the default namespace for saving subscriptions. |
|
303 |
#subscriptions = no |
|
304 |
|
|
305 |
# List the shared/ namespace only if there are visible shared mailboxes. |
|
306 |
#list = children |
|
307 |
#} |
|
308 |
|
|
309 |
# System user and group used to access mails. If you use multiple, userdb |
|
310 |
# can override these by returning uid or gid fields. You can use either numbers |
|
311 |
# or names. <doc/wiki/UserIds.txt> |
|
312 |
#mail_uid = |
|
313 |
#mail_gid = |
|
314 |
|
|
315 |
# Group to enable temporarily for privileged operations. Currently this is |
|
316 |
# used only with INBOX when either its initial creation or dotlocking fails. |
|
317 |
# Typically this is set to "mail" to give access to /var/mail. |
|
318 |
#mail_privileged_group = |
|
319 |
|
|
320 |
# Grant access to these supplementary groups for mail processes. Typically |
|
321 |
# these are used to set up access to shared mailboxes. Note that it may be |
|
322 |
# dangerous to set these if users can create symlinks (e.g. if "mail" group is |
|
323 |
# set here, ln -s /var/mail ~/mail/var could allow a user to delete others' |
|
324 |
# mailboxes, or ln -s /secret/shared/box ~/mail/mybox would allow reading it). |
|
325 |
#mail_access_groups = |
|
326 |
|
|
327 |
# Allow full filesystem access to clients. There's no access checks other than |
|
328 |
# what the operating system does for the active UID/GID. It works with both |
|
329 |
# maildir and mboxes, allowing you to prefix mailboxes names with eg. /path/ |
|
330 |
# or ~user/. |
|
331 |
#mail_full_filesystem_access = no |
|
332 |
|
|
333 |
## |
|
334 |
## Mail processes |
|
335 |
## |
|
336 |
|
|
337 |
# Enable mail process debugging. This can help you figure out why Dovecot |
|
338 |
# isn't finding your mails. |
|
339 |
#mail_debug = no |
|
340 |
|
|
341 |
# Log prefix for mail processes. See <doc/wiki/Variables.txt> for list of |
|
342 |
# possible variables you can use. |
|
343 |
#mail_log_prefix = "%Us(%u): " |
|
344 |
|
|
345 |
# Max. number of lines a mail process is allowed to log per second before it's |
|
346 |
# throttled. 0 means unlimited. Typically there's no need to change this |
|
347 |
# unless you're using mail_log plugin, which may log a lot. This setting is |
|
348 |
# ignored while mail_debug=yes to avoid pointless throttling. |
|
349 |
#mail_log_max_lines_per_sec = 10 |
|
350 |
|
|
351 |
# Don't use mmap() at all. This is required if you store indexes to shared |
|
352 |
# filesystems (NFS or clustered filesystem). |
|
353 |
#mmap_disable = no |
|
354 |
|
|
355 |
# Rely on O_EXCL to work when creating dotlock files. NFS supports O_EXCL |
|
356 |
# since version 3, so this should be safe to use nowadays by default. |
|
357 |
#dotlock_use_excl = yes |
|
358 |
|
|
359 |
# Don't use fsync() or fdatasync() calls. This makes the performance better |
|
360 |
# at the cost of potential data loss if the server (or the file server) |
|
361 |
# goes down. |
|
362 |
#fsync_disable = no |
|
363 |
|
|
364 |
# Mail storage exists in NFS. Set this to yes to make Dovecot flush NFS caches |
|
365 |
# whenever needed. If you're using only a single mail server this isn't needed. |
|
366 |
#mail_nfs_storage = no |
|
367 |
# Mail index files also exist in NFS. Setting this to yes requires |
|
368 |
# mmap_disable=yes and fsync_disable=no. |
|
369 |
#mail_nfs_index = no |
|
370 |
|
|
371 |
# Locking method for index files. Alternatives are fcntl, flock and dotlock. |
|
372 |
# Dotlocking uses some tricks which may create more disk I/O than other locking |
|
373 |
# methods. NFS users: flock doesn't work, remember to change mmap_disable. |
|
374 |
#lock_method = fcntl |
|
375 |
|
|
376 |
# Drop all privileges before exec()ing the mail process. This is mostly |
|
377 |
# meant for debugging, otherwise you don't get core dumps. It could be a small |
|
378 |
# security risk if you use single UID for multiple users, as the users could |
|
379 |
# ptrace() each others processes then. |
|
380 |
#mail_drop_priv_before_exec = no |
|
381 |
|
|
382 |
# Show more verbose process titles (in ps). Currently shows user name and |
|
383 |
# IP address. Useful for seeing who are actually using the IMAP processes |
|
384 |
# (eg. shared mailboxes or if same uid is used for multiple accounts). |
|
385 |
#verbose_proctitle = no |
|
386 |
|
|
387 |
# Valid UID range for users, defaults to 500 and above. This is mostly |
|
388 |
# to make sure that users can't log in as daemons or other system users. |
|
389 |
# Note that denying root logins is hardcoded to dovecot binary and can't |
|
390 |
# be done even if first_valid_uid is set to 0. |
|
391 |
first_valid_uid = 5000 |
|
392 |
last_valid_uid = 5000 |
|
393 |
|
|
394 |
# Valid GID range for users, defaults to non-root/wheel. Users having |
|
395 |
# non-valid GID as primary group ID aren't allowed to log in. If user |
|
396 |
# belongs to supplementary groups with non-valid GIDs, those groups are |
|
397 |
# not set. |
|
398 |
first_valid_gid = 5000 |
|
399 |
last_valid_gid = 5000 |
|
400 |
|
|
401 |
# Maximum number of running mail processes. When this limit is reached, |
|
402 |
# new users aren't allowed to log in. |
|
403 |
#max_mail_processes = 512 |
|
404 |
|
|
405 |
# Set max. process size in megabytes. Most of the memory goes to mmap()ing |
|
406 |
# files, so it shouldn't harm much even if this limit is set pretty high. |
|
407 |
#mail_process_size = 256 |
|
408 |
|
|
409 |
# Maximum allowed length for mail keyword name. It's only forced when trying |
|
410 |
# to create new keywords. |
|
411 |
#mail_max_keyword_length = 50 |
|
412 |
|
|
413 |
# ':' separated list of directories under which chrooting is allowed for mail |
|
414 |
# processes (ie. /var/mail will allow chrooting to /var/mail/foo/bar too). |
|
415 |
# This setting doesn't affect login_chroot, mail_chroot or auth chroot |
|
416 |
# settings. If this setting is empty, "/./" in home dirs are ignored. |
|
417 |
# WARNING: Never add directories here which local users can modify, that |
|
418 |
# may lead to root exploit. Usually this should be done only if you don't |
|
419 |
# allow shell access for users. <doc/wiki/Chrooting.txt> |
|
420 |
#valid_chroot_dirs = |
|
421 |
|
|
422 |
# Default chroot directory for mail processes. This can be overridden for |
|
423 |
# specific users in user database by giving /./ in user's home directory |
|
424 |
# (eg. /home/./user chroots into /home). Note that usually there is no real |
|
425 |
# need to do chrooting, Dovecot doesn't allow users to access files outside |
|
426 |
# their mail directory anyway. If your home directories are prefixed with |
|
427 |
# the chroot directory, append "/." to mail_chroot. <doc/wiki/Chrooting.txt> |
|
428 |
#mail_chroot = |
|
429 |
|
|
430 |
## |
|
431 |
## Mailbox handling optimizations |
|
432 |
## |
|
433 |
|
|
434 |
# The minimum number of mails in a mailbox before updates are done to cache |
|
435 |
# file. This allows optimizing Dovecot's behavior to do less disk writes at |
|
436 |
# the cost of more disk reads. |
|
437 |
#mail_cache_min_mail_count = 0 |
|
438 |
|
|
439 |
# When IDLE command is running, mailbox is checked once in a while to see if |
|
440 |
# there are any new mails or other changes. This setting defines the minimum |
|
441 |
# time in seconds to wait between those checks. Dovecot can also use dnotify, |
|
442 |
# inotify and kqueue to find out immediately when changes occur. |
|
443 |
#mailbox_idle_check_interval = 30 |
|
444 |
|
|
445 |
# Save mails with CR+LF instead of plain LF. This makes sending those mails |
|
446 |
# take less CPU, especially with sendfile() syscall with Linux and FreeBSD. |
|
447 |
# But it also creates a bit more disk I/O which may just make it slower. |
|
448 |
# Also note that if other software reads the mboxes/maildirs, they may handle |
|
449 |
# the extra CRs wrong and cause problems. |
|
450 |
#mail_save_crlf = no |
|
451 |
|
|
452 |
## |
|
453 |
## Maildir-specific settings |
|
454 |
## |
|
455 |
|
|
456 |
# By default LIST command returns all entries in maildir beginning with a dot. |
|
457 |
# Enabling this option makes Dovecot return only entries which are directories. |
|
458 |
# This is done by stat()ing each entry, so it causes more disk I/O. |
|
459 |
# (For systems setting struct dirent->d_type, this check is free and it's |
|
460 |
# done always regardless of this setting) |
|
461 |
#maildir_stat_dirs = no |
|
462 |
|
|
463 |
# When copying a message, do it with hard links whenever possible. This makes |
|
464 |
# the performance much better, and it's unlikely to have any side effects. |
|
465 |
#maildir_copy_with_hardlinks = yes |
|
466 |
|
|
467 |
# When copying a message, try to preserve the base filename. Only if the |
|
468 |
# destination mailbox already contains the same name (ie. the mail is being |
|
469 |
# copied there twice), a new name is given. The destination filename check is |
|
470 |
# done only by looking at dovecot-uidlist file, so if something outside |
|
471 |
# Dovecot does similar filename preserving copies, you may run into problems. |
|
472 |
# NOTE: This setting requires maildir_copy_with_hardlinks = yes to work. |
|
473 |
#maildir_copy_preserve_filename = no |
|
474 |
|
|
475 |
# Assume Dovecot is the only MUA accessing Maildir: Scan cur/ directory only |
|
476 |
# when its mtime changes unexpectedly or when we can't find the mail otherwise. |
|
477 |
#maildir_very_dirty_syncs = no |
|
478 |
|
|
479 |
## |
|
480 |
## mbox-specific settings |
|
481 |
## |
|
482 |
|
|
483 |
# Which locking methods to use for locking mbox. There are four available: |
|
484 |
# dotlock: Create <mailbox>.lock file. This is the oldest and most NFS-safe |
|
485 |
# solution. If you want to use /var/mail/ like directory, the users |
|
486 |
# will need write access to that directory. |
|
487 |
# dotlock_try: Same as dotlock, but if it fails because of permissions or |
|
488 |
# because there isn't enough disk space, just skip it. |
|
489 |
# fcntl : Use this if possible. Works with NFS too if lockd is used. |
|
490 |
# flock : May not exist in all systems. Doesn't work with NFS. |
|
491 |
# lockf : May not exist in all systems. Doesn't work with NFS. |
|
492 |
# |
|
493 |
# You can use multiple locking methods; if you do the order they're declared |
|
494 |
# in is important to avoid deadlocks if other MTAs/MUAs are using multiple |
|
495 |
# locking methods as well. Some operating systems don't allow using some of |
|
496 |
# them simultaneously. |
|
497 |
#mbox_read_locks = fcntl |
|
498 |
#mbox_write_locks = dotlock fcntl |
|
499 |
|
|
500 |
# Maximum time in seconds to wait for lock (all of them) before aborting. |
|
501 |
#mbox_lock_timeout = 300 |
|
502 |
|
|
503 |
# If dotlock exists but the mailbox isn't modified in any way, override the |
|
504 |
# lock file after this many seconds. |
|
505 |
#mbox_dotlock_change_timeout = 120 |
|
506 |
|
|
507 |
# When mbox changes unexpectedly we have to fully read it to find out what |
|
508 |
# changed. If the mbox is large this can take a long time. Since the change |
|
509 |
# is usually just a newly appended mail, it'd be faster to simply read the |
|
510 |
# new mails. If this setting is enabled, Dovecot does this but still safely |
|
511 |
# fallbacks to re-reading the whole mbox file whenever something in mbox isn't |
|
512 |
# how it's expected to be. The only real downside to this setting is that if |
|
513 |
# some other MUA changes message flags, Dovecot doesn't notice it immediately. |
|
514 |
# Note that a full sync is done with SELECT, EXAMINE, EXPUNGE and CHECK |
|
515 |
# commands. |
|
516 |
#mbox_dirty_syncs = yes |
|
517 |
|
|
518 |
# Like mbox_dirty_syncs, but don't do full syncs even with SELECT, EXAMINE, |
|
519 |
# EXPUNGE or CHECK commands. If this is set, mbox_dirty_syncs is ignored. |
|
520 |
#mbox_very_dirty_syncs = no |
|
521 |
|
|
522 |
# Delay writing mbox headers until doing a full write sync (EXPUNGE and CHECK |
|
523 |
# commands and when closing the mailbox). This is especially useful for POP3 |
|
524 |
# where clients often delete all mails. The downside is that our changes |
|
525 |
# aren't immediately visible to other MUAs. |
|
526 |
#mbox_lazy_writes = yes |
|
527 |
|
|
528 |
# If mbox size is smaller than this (in kilobytes), don't write index files. |
|
529 |
# If an index file already exists it's still read, just not updated. |
|
530 |
#mbox_min_index_size = 0 |
|
531 |
|
|
532 |
## |
|
533 |
## dbox-specific settings |
|
534 |
## |
|
535 |
|
|
536 |
# Maximum dbox file size in kilobytes until it's rotated. |
|
537 |
#dbox_rotate_size = 2048 |
|
538 |
|
|
539 |
# Minimum dbox file size in kilobytes before it's rotated |
|
540 |
# (overrides dbox_rotate_days) |
|
541 |
#dbox_rotate_min_size = 16 |
|
542 |
|
|
543 |
# Maximum dbox file age in days until it's rotated. Day always begins from |
|
544 |
# midnight, so 1 = today, 2 = yesterday, etc. 0 = check disabled. |
|
545 |
#dbox_rotate_days = 0 |
|
546 |
|
|
547 |
## |
|
548 |
## IMAP specific settings |
|
549 |
## |
|
550 |
|
|
551 |
protocol imap { |
|
552 |
# Login executable location. |
|
553 |
#login_executable = /usr/lib/dovecot/imap-login |
|
554 |
|
|
555 |
# IMAP executable location. Changing this allows you to execute other |
|
556 |
# binaries before the imap process is executed. |
|
557 |
# |
|
558 |
# This would write rawlogs into user's ~/dovecot.rawlog/, if it exists: |
|
559 |
# mail_executable = /usr/lib/dovecot/rawlog /usr/lib/dovecot/imap |
|
560 |
# <doc/wiki/Debugging/Rawlog.txt> |
|
561 |
# |
|
562 |
# This would attach gdb into the imap process and write backtraces into |
|
563 |
# /tmp/gdbhelper.* files: |
|
564 |
# mail_executable = /usr/lib/dovecot/gdbhelper /usr/lib/dovecot/imap |
|
565 |
# |
|
566 |
#mail_executable = /usr/lib/dovecot/imap |
|
567 |
mail_executable = /usr/lib/dovecot/rawlog /usr/lib/dovecot/imap |
|
568 |
|
|
569 |
# Maximum IMAP command line length in bytes. Some clients generate very long |
|
570 |
# command lines with huge mailboxes, so you may need to raise this if you get |
|
571 |
# "Too long argument" or "IMAP command line too large" errors often. |
|
572 |
#imap_max_line_length = 65536 |
|
573 |
|
|
574 |
# Maximum number of IMAP connections allowed for a user from each IP address. |
|
575 |
# NOTE: The username is compared case-sensitively. |
|
576 |
#mail_max_userip_connections = 10 |
|
577 |
|
|
578 |
# Support for dynamically loadable plugins. mail_plugins is a space separated |
|
579 |
# list of plugins to load. |
|
580 |
#mail_plugins = |
|
581 |
mail_plugins = quota imap_quota |
|
582 |
mail_plugin_dir = /usr/lib/dovecot/modules/imap |
|
583 |
|
|
584 |
# IMAP logout format string: |
|
585 |
# %i - total number of bytes read from client |
|
586 |
# %o - total number of bytes sent to client |
|
587 |
#imap_logout_format = bytes=%i/%o |
|
588 |
|
|
589 |
# Override the IMAP CAPABILITY response. |
|
590 |
#imap_capability = |
|
591 |
|
|
592 |
# How many seconds to wait between "OK Still here" notifications when |
|
593 |
# client is IDLEing. |
|
594 |
#imap_idle_notify_interval = 120 |
|
595 |
|
|
596 |
# ID field names and values to send to clients. Using * as the value makes |
|
597 |
# Dovecot use the default value. The following fields have default values |
|
598 |
# currently: name, version, os, os-version, support-url, support-email. |
|
599 |
#imap_id_send = |
|
600 |
|
|
601 |
# ID fields sent by client to log. * means everything. |
|
602 |
#imap_id_log = |
|
603 |
|
|
604 |
# Workarounds for various client bugs: |
|
605 |
# delay-newmail: |
|
606 |
# Send EXISTS/RECENT new mail notifications only when replying to NOOP |
|
607 |
# and CHECK commands. Some clients ignore them otherwise, for example OSX |
|
608 |
# Mail (<v2.1). Outlook Express breaks more badly though, without this it |
|
609 |
# may show user "Message no longer in server" errors. Note that OE6 still |
|
610 |
# breaks even with this workaround if synchronization is set to |
|
611 |
# "Headers Only". |
|
612 |
# netscape-eoh: |
|
613 |
# Netscape 4.x breaks if message headers don't end with the empty "end of |
|
614 |
# headers" line. Normally all messages have this, but setting this |
|
615 |
# workaround makes sure that Netscape never breaks by adding the line if |
|
616 |
# it doesn't exist. This is done only for FETCH BODY[HEADER.FIELDS..] |
|
617 |
# commands. Note that RFC says this shouldn't be done. |
|
618 |
# tb-extra-mailbox-sep: |
|
619 |
# With mbox storage a mailbox can contain either mails or submailboxes, |
|
620 |
# but not both. Thunderbird separates these two by forcing server to |
|
621 |
# accept '/' suffix in mailbox names in subscriptions list. |
|
622 |
# The list is space-separated. |
|
623 |
#imap_client_workarounds = |
|
624 |
} |
|
625 |
|
|
626 |
## |
|
627 |
## POP3 specific settings |
|
628 |
## |
|
629 |
|
|
630 |
protocol pop3 { |
|
631 |
# Login executable location. |
|
632 |
#login_executable = /usr/lib/dovecot/pop3-login |
|
633 |
|
|
634 |
# POP3 executable location. See IMAP's mail_executable above for examples |
|
635 |
# how this could be changed. |
|
636 |
#mail_executable = /usr/lib/dovecot/pop3 |
|
637 |
mail_executable = /usr/lib/dovecot/rawlog /usr/lib/dovecot/pop3 |
|
638 |
|
|
639 |
# Don't try to set mails non-recent or seen with POP3 sessions. This is |
|
640 |
# mostly intended to reduce disk I/O. With maildir it doesn't move files |
|
641 |
# from new/ to cur/, with mbox it doesn't write Status-header. |
|
642 |
#pop3_no_flag_updates = no |
|
643 |
|
|
644 |
# Support LAST command which exists in old POP3 specs, but has been removed |
|
645 |
# from new ones. Some clients still wish to use this though. Enabling this |
|
646 |
# makes RSET command clear all \Seen flags from messages. |
|
647 |
#pop3_enable_last = no |
|
648 |
|
|
649 |
# If mail has X-UIDL header, use it as the mail's UIDL. |
|
650 |
#pop3_reuse_xuidl = no |
|
651 |
|
|
652 |
# Keep the mailbox locked for the entire POP3 session. |
|
653 |
#pop3_lock_session = no |
|
654 |
|
|
655 |
# POP3 UIDL (unique mail identifier) format to use. You can use following |
|
656 |
# variables, along with the variable modifiers described in |
|
657 |
# <doc/wiki/Variables.txt> (e.g. %Uf for the filename in uppercase) |
|
658 |
# |
|
659 |
# %v - Mailbox's IMAP UIDVALIDITY |
|
660 |
# %u - Mail's IMAP UID |
|
661 |
# %m - MD5 sum of the mailbox headers in hex (mbox only) |
|
662 |
# %f - filename (maildir only) |
|
663 |
# |
|
664 |
# If you want UIDL compatibility with other POP3 servers, use: |
|
665 |
# UW's ipop3d : %08Xv%08Xu |
|
666 |
# Courier : %f or %v-%u (both might be used simultaneosly) |
|
667 |
# Cyrus (<= 2.1.3) : %u |
|
668 |
# Cyrus (>= 2.1.4) : %v.%u |
|
669 |
# Dovecot v0.99.x : %v.%u |
|
670 |
# tpop3d : %Mf |
|
671 |
# |
|
672 |
# Note that Outlook 2003 seems to have problems with %v.%u format which was |
|
673 |
# Dovecot's default, so if you're building a new server it would be a good |
|
674 |
# idea to change this. %08Xu%08Xv should be pretty fail-safe. |
|
675 |
# |
|
676 |
#pop3_uidl_format = %08Xu%08Xv |
|
677 |
pop3_uidl_format = %08Xu%08Xv |
|
678 |
|
|
679 |
# Permanently save UIDLs sent to POP3 clients, so pop3_uidl_format changes |
|
680 |
# won't change those UIDLs. Currently this works only with Maildir. |
|
681 |
#pop3_save_uidl = no |
|
682 |
|
|
683 |
# POP3 logout format string: |
|
684 |
# %i - total number of bytes read from client |
|
685 |
# %o - total number of bytes sent to client |
|
686 |
# %t - number of TOP commands |
|
687 |
# %p - number of bytes sent to client as a result of TOP command |
|
688 |
# %r - number of RETR commands |
|
689 |
# %b - number of bytes sent to client as a result of RETR command |
|
690 |
# %d - number of deleted messages |
|
691 |
# %m - number of messages (before deletion) |
|
692 |
# %s - mailbox size in bytes (before deletion) |
|
693 |
#pop3_logout_format = top=%t/%p, retr=%r/%b, del=%d/%m, size=%s |
|
694 |
|
|
695 |
# Maximum number of POP3 connections allowed for a user from each IP address. |
|
696 |
# NOTE: The username is compared case-sensitively. |
|
697 |
#mail_max_userip_connections = 3 |
|
698 |
|
|
699 |
# Support for dynamically loadable plugins. mail_plugins is a space separated |
|
700 |
# list of plugins to load. |
|
701 |
#mail_plugins = |
|
702 |
mail_plugins = quota |
|
703 |
mail_plugin_dir = /usr/lib/dovecot/modules/pop3 |
|
704 |
|
|
705 |
# Workarounds for various client bugs: |
|
706 |
# outlook-no-nuls: |
|
707 |
# Outlook and Outlook Express hang if mails contain NUL characters. |
|
708 |
# This setting replaces them with 0x80 character. |
|
709 |
# oe-ns-eoh: |
|
710 |
# Outlook Express and Netscape Mail breaks if end of headers-line is |
|
711 |
# missing. This option simply sends it if it's missing. |
|
712 |
# The list is space-separated. |
|
713 |
#pop3_client_workarounds = |
|
714 |
} |
|
715 |
|
|
716 |
## |
|
717 |
## ManageSieve specific settings |
|
718 |
## |
|
719 |
|
|
720 |
protocol managesieve { |
|
721 |
# Login executable location. |
|
722 |
#login_executable = /usr/lib/dovecot/managesieve-login |
|
723 |
|
|
724 |
# ManageSieve executable location. See IMAP's mail_executable above for |
|
725 |
# examples how this could be changed. |
|
726 |
#mail_executable = /usr/lib/dovecot/managesieve |
|
727 |
|
|
728 |
# Maximum ManageSieve command line length in bytes. This setting is |
|
729 |
# directly borrowed from IMAP. But, since long command lines are very |
|
730 |
# unlikely with ManageSieve, changing this will not be very useful. |
|
731 |
#managesieve_max_line_length = 65536 |
|
732 |
|
|
733 |
# ManageSieve logout format string: |
|
734 |
# %i - total number of bytes read from client |
|
735 |
# %o - total number of bytes sent to client |
|
736 |
#managesieve_logout_format = bytes=%i/%o |
|
737 |
|
|
738 |
# If, for some inobvious reason, the sieve_storage remains unset, the |
|
739 |
# ManageSieve daemon uses the specification of the mail_location to find out |
|
740 |
# where to store the sieve files (see explaination in README.managesieve). |
|
741 |
# The example below, when uncommented, overrides any global mail_location |
|
742 |
# specification and stores all the scripts in '~/mail/sieve' if sieve_storage |
|
743 |
# is unset. However, you should always use the sieve_storage setting. |
|
744 |
# mail_location = mbox:~/mail |
|
745 |
|
|
746 |
# To fool ManageSieve clients that are focused on timesieved you can |
|
747 |
# specify the IMPLEMENTATION capability that the dovecot reports to clients |
|
748 |
# (default: "dovecot"). |
|
749 |
#managesieve_implementation_string = Cyrus timsieved v2.2.13 |
|
750 |
} |
|
751 |
|
|
752 |
## |
|
753 |
## LDA specific settings |
|
754 |
## |
|
755 |
|
|
756 |
protocol lda { |
|
757 |
# Address to use when sending rejection mails. |
|
758 |
postmaster_address = postmaster@example.com |
|
759 |
|
|
760 |
# Hostname to use in various parts of sent mails, eg. in Message-Id. |
|
761 |
# Default is the system's real hostname. |
|
762 |
#hostname = |
|
763 |
|
|
764 |
# Support for dynamically loadable plugins. mail_plugins is a space separated |
|
765 |
# list of plugins to load. |
|
766 |
#mail_plugins = |
|
767 |
mail_plugins = sieve quota |
|
768 |
mail_plugin_dir = /usr/lib/dovecot/modules/lda |
|
769 |
|
|
770 |
# If user is over quota, return with temporary failure instead of |
|
771 |
# bouncing the mail. |
|
772 |
#quota_full_tempfail = no |
|
773 |
|
|
774 |
# Format to use for logging mail deliveries. You can use variables: |
|
775 |
# %$ - Delivery status message (e.g. "saved to INBOX") |
|
776 |
# %m - Message-ID |
|
777 |
# %s - Subject |
|
778 |
# %f - From address |
|
779 |
#deliver_log_format = msgid=%m: %$ |
|
780 |
|
|
781 |
# Binary to use for sending mails. |
|
782 |
#sendmail_path = /usr/lib/sendmail |
|
783 |
|
|
784 |
# Subject: header to use for rejection mails. You can use the same variables |
|
785 |
# as for rejection_reason below. |
|
786 |
#rejection_subject = Rejected: %s |
|
787 |
|
|
788 |
# Human readable error message for rejection mails. You can use variables: |
|
789 |
# %n = CRLF, %r = reason, %s = original subject, %t = recipient |
|
790 |
#rejection_reason = Your message to <%t> was automatically rejected:%n%r |
|
791 |
|
|
792 |
# UNIX socket path to master authentication server to find users. |
|
793 |
auth_socket_path = /var/run/dovecot/auth-master |
|
794 |
} |
|
795 |
|
|
796 |
## |
|
797 |
## Authentication processes |
|
798 |
## |
|
799 |
|
|
800 |
# Executable location |
|
801 |
#auth_executable = /usr/lib/dovecot/dovecot-auth |
|
802 |
|
|
803 |
# Set max. process size in megabytes. |
|
804 |
#auth_process_size = 256 |
|
805 |
|
|
806 |
# Authentication cache size in kilobytes. 0 means it's disabled. |
|
807 |
# Note that bsdauth, PAM and vpopmail require cache_key to be set for caching |
|
808 |
# to be used. |
|
809 |
#auth_cache_size = 0 |
|
810 |
# Time to live in seconds for cached data. After this many seconds the cached |
|
811 |
# record is no longer used, *except* if the main database lookup returns |
|
812 |
# internal failure. We also try to handle password changes automatically: If |
|
813 |
# user's previous authentication was successful, but this one wasn't, the |
|
814 |
# cache isn't used. For now this works only with plaintext authentication. |
|
815 |
#auth_cache_ttl = 3600 |
|
816 |
# TTL for negative hits (user not found, password mismatch). |
|
817 |
# 0 disables caching them completely. |
|
818 |
#auth_cache_negative_ttl = 3600 |
|
819 |
|
|
820 |
# Space separated list of realms for SASL authentication mechanisms that need |
|
821 |
# them. You can leave it empty if you don't want to support multiple realms. |
|
822 |
# Many clients simply use the first one listed here, so keep the default realm |
|
823 |
# first. |
|
824 |
#auth_realms = |
|
825 |
|
|
826 |
# Default realm/domain to use if none was specified. This is used for both |
|
827 |
# SASL realms and appending @domain to username in plaintext logins. |
|
828 |
#auth_default_realm = |
|
829 |
|
|
830 |
# List of allowed characters in username. If the user-given username contains |
|
831 |
# a character not listed in here, the login automatically fails. This is just |
|
832 |
# an extra check to make sure user can't exploit any potential quote escaping |
|
833 |
# vulnerabilities with SQL/LDAP databases. If you want to allow all characters, |
|
834 |
# set this value to empty. |
|
835 |
#auth_username_chars = abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ01234567890.-_@ |
|
836 |
|
|
837 |
# Username character translations before it's looked up from databases. The |
|
838 |
# value contains series of from -> to characters. For example "#@/@" means |
|
839 |
# that '#' and '/' characters are translated to '@'. |
|
840 |
#auth_username_translation = |
|
841 |
|
|
842 |
# Username formatting before it's looked up from databases. You can use |
|
843 |
# the standard variables here, eg. %Lu would lowercase the username, %n would |
|
844 |
# drop away the domain if it was given, or "%n-AT-%d" would change the '@' into |
|
845 |
# "-AT-". This translation is done after auth_username_translation changes. |
|
846 |
#auth_username_format = |
|
847 |
|
|
848 |
# If you want to allow master users to log in by specifying the master |
|
849 |
# username within the normal username string (ie. not using SASL mechanism's |
|
850 |
# support for it), you can specify the separator character here. The format |
|
851 |
# is then <username><separator><master username>. UW-IMAP uses "*" as the |
|
852 |
# separator, so that could be a good choice. |
|
853 |
#auth_master_user_separator = |
|
854 |
|
|
855 |
# Username to use for users logging in with ANONYMOUS SASL mechanism |
|
856 |
#auth_anonymous_username = anonymous |
|
857 |
|
|
858 |
# Log unsuccessful authentication attempts and the reasons why they failed. |
|
859 |
#auth_verbose = no |
|
860 |
|
|
861 |
# Even more verbose logging for debugging purposes. Shows for example SQL |
|
862 |
# queries. |
|
863 |
#auth_debug = no |
|
864 |
|
|
865 |
# In case of password mismatches, log the passwords and used scheme so the |
|
866 |
# problem can be debugged. Enabling this also enables auth_debug. |
|
867 |
#auth_debug_passwords = no |
|
868 |
|
|
869 |
# Maximum number of dovecot-auth worker processes. They're used to execute |
|
870 |
# blocking passdb and userdb queries (eg. MySQL and PAM). They're |
|
871 |
# automatically created and destroyed as needed. |
|
872 |
#auth_worker_max_count = 30 |
|
873 |
|
|
874 |
# Host name to use in GSSAPI principal names. The default is to use the |
|
875 |
# name returned by gethostname(). Use "$ALL" to allow all keytab entries. |
|
876 |
#auth_gssapi_hostname = |
|
877 |
|
|
878 |
# Kerberos keytab to use for the GSSAPI mechanism. Will use the system |
|
879 |
# default (usually /etc/krb5.keytab) if not specified. |
|
880 |
#auth_krb5_keytab = |
|
881 |
|
|
882 |
# Do NTLM and GSS-SPNEGO authentication using Samba's winbind daemon and |
|
883 |
# ntlm_auth helper. <doc/wiki/Authentication/Mechanisms/Winbind.txt> |
|
884 |
#auth_use_winbind = no |
|
885 |
|
|
886 |
# Path for Samba's ntlm_auth helper binary. |
|
887 |
#auth_winbind_helper_path = /usr/bin/ntlm_auth |
|
888 |
|
|
889 |
# Number of seconds to delay before replying to failed authentications. |
|
890 |
#auth_failure_delay = 2 |
|
891 |
|
|
892 |
auth default { |
|
893 |
# Space separated list of wanted authentication mechanisms: |
|
894 |
# plain login digest-md5 cram-md5 ntlm rpa apop anonymous gssapi otp skey |
|
895 |
# gss-spnego |
|
896 |
# NOTE: See also disable_plaintext_auth setting. |
|
897 |
mechanisms = plain login |
|
898 |
|
|
899 |
# |
|
900 |
# Password database is used to verify user's password (and nothing more). |
|
901 |
# You can have multiple passdbs and userdbs. This is useful if you want to |
|
902 |
# allow both system users (/etc/passwd) and virtual users to login without |
|
903 |
# duplicating the system users into virtual database. |
|
904 |
# |
|
905 |
# <doc/wiki/PasswordDatabase.txt> |
|
906 |
# |
|
907 |
# By adding master=yes setting inside a passdb you make the passdb a list |
|
908 |
# of "master users", who can log in as anyone else. Unless you're using PAM, |
|
909 |
# you probably still want the destination user to be looked up from passdb |
|
910 |
# that it really exists. This can be done by adding pass=yes setting to the |
|
911 |
# master passdb. <doc/wiki/Authentication.MasterUsers.txt> |
|
912 |
|
|
913 |
# Users can be temporarily disabled by adding a passdb with deny=yes. |
|
914 |
# If the user is found from that database, authentication will fail. |
|
915 |
# The deny passdb should always be specified before others, so it gets |
|
916 |
# checked first. Here's an example: |
|
917 |
|
|
918 |
#passdb passwd-file { |
|
919 |
# File contains a list of usernames, one per line |
|
920 |
#args = /etc/dovecot.deny |
|
921 |
#deny = yes |
|
922 |
#} |
|
923 |
|
|
924 |
# PAM authentication. Preferred nowadays by most systems. |
|
925 |
# Note that PAM can only be used to verify if user's password is correct, |
|
926 |
# so it can't be used as userdb. If you don't want to use a separate user |
|
927 |
# database (passwd usually), you can use static userdb. |
|
928 |
# REMEMBER: You'll need /etc/pam.d/dovecot file created for PAM |
|
929 |
# authentication to actually work. <doc/wiki/PasswordDatabase.PAM.txt> |
|
930 |
passdb pam { |
|
931 |
# [session=yes] [setcred=yes] [failure_show_msg=yes] [max_requests=<n>] |
|
932 |
# [cache_key=<key>] [<service name>] |
|
933 |
# |
|
934 |
# session=yes makes Dovecot open and immediately close PAM session. Some |
|
935 |
# PAM plugins need this to work, such as pam_mkhomedir. |
|
936 |
# |
|
937 |
# setcred=yes makes Dovecot establish PAM credentials if some PAM plugins |
|
938 |
# need that. They aren't ever deleted though, so this isn't enabled by |
|
939 |
# default. |
|
940 |
# |
|
941 |
# max_requests specifies how many PAM lookups to do in one process before |
|
942 |
# recreating the process. The default is 100, because many PAM plugins |
|
943 |
# leak memory. |
|
944 |
# |
|
945 |
# cache_key can be used to enable authentication caching for PAM |
|
946 |
# (auth_cache_size also needs to be set). It isn't enabled by default |
|
947 |
# because PAM modules can do all kinds of checks besides checking password, |
|
948 |
# such as checking IP address. Dovecot can't know about these checks |
|
949 |
# without some help. cache_key is simply a list of variables (see |
|
950 |
# doc/wiki/Variables.txt) which must match for the cached data to be used. |
|
951 |
# Here are some examples: |
|
952 |
# %u - Username must match. Probably sufficient for most uses. |
|
953 |
# %u%r - Username and remote IP address must match. |
|
954 |
# %u%s - Username and service (ie. IMAP, POP3) must match. |
|
955 |
# |
|
956 |
# The service name can contain variables, for example %Ls expands to |
|
957 |
# pop3 or imap. |
|
958 |
# |
|
959 |
# Some examples: |
|
960 |
# args = session=yes %Ls |
|
961 |
# args = cache_key=%u dovecot |
|
962 |
#args = dovecot |
|
963 |
} |
|
964 |
|
|
965 |
# System users (NSS, /etc/passwd, or similiar) |
|
966 |
# In many systems nowadays this uses Name Service Switch, which is |
|
967 |
# configured in /etc/nsswitch.conf. <doc/wiki/AuthDatabase.Passwd.txt> |
|
968 |
#passdb passwd { |
|
969 |
# [blocking=yes] - See userdb passwd for explanation |
|
970 |
#args = |
|
971 |
#} |
|
972 |
|
|
973 |
# Shadow passwords for system users (NSS, /etc/shadow or similiar). |
|
974 |
# Deprecated by PAM nowadays. |
|
975 |
# <doc/wiki/PasswordDatabase.Shadow.txt> |
|
976 |
#passdb shadow { |
|
977 |
# [blocking=yes] - See userdb passwd for explanation |
|
978 |
#args = |
|
979 |
#} |
|
980 |
|
|
981 |
# PAM-like authentication for OpenBSD. |
|
982 |
# <doc/wiki/PasswordDatabase.BSDAuth.txt> |
|
983 |
#passdb bsdauth { |
|
984 |
# [cache_key=<key>] - See cache_key in PAM for explanation. |
|
985 |
#args = |
|
986 |
#} |
|
987 |
|
|
988 |
# passwd-like file with specified location |
|
989 |
# <doc/wiki/AuthDatabase.PasswdFile.txt> |
|
990 |
#passdb passwd-file { |
|
991 |
# [scheme=<default password scheme>] [username_format=<format>] |
|
992 |
# <Path for passwd-file> |
|
993 |
#args = |
|
994 |
#} |
|
995 |
|
|
996 |
# checkpassword executable authentication |
|
997 |
# NOTE: You will probably want to use "userdb prefetch" with this. |
|
998 |
# <doc/wiki/AuthDatabase.CheckPassword.txt> |
|
999 |
#passdb checkpassword { |
|
1000 |
# Path for checkpassword binary |
|
1001 |
#args = |
|
1002 |
#} |
|
1003 |
|
|
1004 |
# SQL database <doc/wiki/AuthDatabase.SQL.txt> |
|
1005 |
passdb sql { |
|
1006 |
# Path for SQL configuration file, see doc/dovecot-sql-example.conf |
|
1007 |
args = /etc/dovecot/dovecot-sql.conf |
|
1008 |
} |
|
1009 |
|
|
1010 |
# LDAP database <doc/wiki/AuthDatabase.LDAP.txt> |
|
1011 |
#passdb ldap { |
|
1012 |
# Path for LDAP configuration file, see doc/dovecot-ldap-example.conf |
|
1013 |
#args = |
|
1014 |
#} |
|
1015 |
|
|
1016 |
# vpopmail authentication <doc/wiki/AuthDatabase.VPopMail.txt> |
|
1017 |
#passdb vpopmail { |
|
1018 |
# [cache_key=<key>] - See cache_key in PAM for explanation. |
|
1019 |
# [quota_template=<template>] - %q expands to Maildir++ quota |
|
1020 |
# (eg. quota_template=quota_rule=*:backend=%q) |
|
1021 |
#args = |
|
1022 |
#} |
|
1023 |
|
|
1024 |
# |
|
1025 |
# User database specifies where mails are located and what user/group IDs |
|
1026 |
# own them. For single-UID configuration use "static". |
|
1027 |
# |
|
1028 |
# <doc/wiki/UserDatabase.txt> |
|
1029 |
# |
|
1030 |
|
|
1031 |
# "prefetch" user database means that the passdb already provided the |
|
1032 |
# needed information and there's no need to do a separate userdb lookup. |
|
1033 |
# This can be made to work with SQL and LDAP databases, see their example |
|
1034 |
# configuration files for more information how to do it. |
|
1035 |
# <doc/wiki/UserDatabase.Prefetch.txt> |
03b633
|
1036 |
userdb prefetch { |
D |
1037 |
} |
fdb514
|
1038 |
|
T |
1039 |
# System users (NSS, /etc/passwd, or similiar). In many systems nowadays this |
|
1040 |
# uses Name Service Switch, which is configured in /etc/nsswitch.conf. |
|
1041 |
# <doc/wiki/AuthDatabase.Passwd.txt> |
|
1042 |
userdb passwd { |
|
1043 |
# [blocking=yes] - By default the lookups are done in the main dovecot-auth |
|
1044 |
# process. This setting causes the lookups to be done in auth worker |
|
1045 |
# proceses. Useful with remote NSS lookups that may block. |
|
1046 |
# NOTE: Be sure to use this setting with nss_ldap or users might get |
|
1047 |
# logged in as each others! |
|
1048 |
#args = |
|
1049 |
} |
|
1050 |
|
|
1051 |
# passwd-like file with specified location |
|
1052 |
# <doc/wiki/AuthDatabase.PasswdFile.txt> |
|
1053 |
#userdb passwd-file { |
|
1054 |
# [username_format=<format>] <Path for passwd-file> |
|
1055 |
#args = |
|
1056 |
#} |
|
1057 |
|
|
1058 |
# checkpassword executable user database lookup |
|
1059 |
# <doc/wiki/AuthDatabase.CheckPassword.txt> |
|
1060 |
#userdb checkpassword { |
|
1061 |
# Path for checkpassword binary |
|
1062 |
#args = |
|
1063 |
#} |
|
1064 |
|
|
1065 |
# static settings generated from template <doc/wiki/UserDatabase.Static.txt> |
|
1066 |
#userdb static { |
|
1067 |
# Template for the fields. Can return anything a userdb could normally |
|
1068 |
# return. For example: |
|
1069 |
# |
|
1070 |
# args = uid=500 gid=500 home=/var/mail/%u |
|
1071 |
# |
|
1072 |
# If you use deliver, it needs to look up users only from the userdb. This |
|
1073 |
# of course doesn't work with static because there is no list of users. |
|
1074 |
# Normally static userdb handles this by doing a passdb lookup. This works |
|
1075 |
# with most passdbs, with PAM being the most notable exception. If you do |
|
1076 |
# the user verification another way, you can add allow_all_users=yes to |
|
1077 |
# the args in which case the passdb lookup is skipped. |
|
1078 |
# |
|
1079 |
#args = |
|
1080 |
#} |
|
1081 |
|
|
1082 |
# SQL database <doc/wiki/AuthDatabase.SQL.txt> |
|
1083 |
userdb sql { |
|
1084 |
# Path for SQL configuration file, see doc/dovecot-sql-example.conf |
|
1085 |
args = /etc/dovecot/dovecot-sql.conf |
|
1086 |
} |
|
1087 |
|
|
1088 |
# LDAP database <doc/wiki/AuthDatabase.LDAP.txt> |
|
1089 |
#userdb ldap { |
|
1090 |
# Path for LDAP configuration file, see doc/dovecot-ldap-example.conf |
|
1091 |
#args = |
|
1092 |
#} |
|
1093 |
|
|
1094 |
# vpopmail <doc/wiki/AuthDatabase.VPopMail.txt> |
|
1095 |
#userdb vpopmail { |
|
1096 |
#} |
|
1097 |
|
|
1098 |
# User to use for the process. This user needs access to only user and |
|
1099 |
# password databases, nothing else. Only shadow and pam authentication |
|
1100 |
# requires roots, so use something else if possible. Note that passwd |
|
1101 |
# authentication with BSDs internally accesses shadow files, which also |
|
1102 |
# requires roots. Note that this user is NOT used to access mails. |
|
1103 |
# That user is specified by userdb above. |
|
1104 |
user = root |
|
1105 |
|
|
1106 |
# Directory where to chroot the process. Most authentication backends don't |
|
1107 |
# work if this is set, and there's no point chrooting if auth_user is root. |
|
1108 |
# Note that valid_chroot_dirs isn't needed to use this setting. |
|
1109 |
#chroot = |
|
1110 |
|
|
1111 |
# Number of authentication processes to create |
|
1112 |
#count = 1 |
|
1113 |
|
|
1114 |
# Require a valid SSL client certificate or the authentication fails. |
|
1115 |
#ssl_require_client_cert = no |
|
1116 |
|
|
1117 |
# Take the username from client's SSL certificate, using |
|
1118 |
# X509_NAME_get_text_by_NID() which returns the subject's DN's |
|
1119 |
# CommonName. |
|
1120 |
#ssl_username_from_cert = no |
|
1121 |
|
|
1122 |
# It's possible to export the authentication interface to other programs: |
|
1123 |
socket listen { |
|
1124 |
master { |
|
1125 |
# Master socket provides access to userdb information. It's typically |
|
1126 |
# used to give Dovecot's local delivery agent access to userdb so it |
|
1127 |
# can find mailbox locations. |
|
1128 |
path = /var/run/dovecot/auth-master |
|
1129 |
mode = 0600 |
|
1130 |
# Default user/group is the one who started dovecot-auth (root) |
|
1131 |
user = vmail |
|
1132 |
#group = |
|
1133 |
} |
|
1134 |
client { |
|
1135 |
# The client socket is generally safe to export to everyone. Typical use |
|
1136 |
# is to export it to your SMTP server so it can do SMTP AUTH lookups |
|
1137 |
# using it. |
|
1138 |
path = /var/spool/postfix/private/auth |
|
1139 |
mode = 0660 |
|
1140 |
user = postfix |
|
1141 |
group = postfix |
|
1142 |
} |
|
1143 |
} |
|
1144 |
} |
|
1145 |
|
|
1146 |
# If you wish to use another authentication server than dovecot-auth, you can |
|
1147 |
# use connect sockets. They are assumed to be already running, Dovecot's master |
|
1148 |
# process only tries to connect to them. They don't need any other settings |
|
1149 |
# than the path for the master socket, as the configuration is done elsewhere. |
|
1150 |
# Note that the client sockets must exist in the login_dir. |
|
1151 |
#auth external { |
|
1152 |
# socket connect { |
|
1153 |
# master { |
|
1154 |
# path = /var/run/dovecot/auth-master |
|
1155 |
# } |
|
1156 |
# } |
|
1157 |
#} |
|
1158 |
|
|
1159 |
## |
|
1160 |
## Dictionary server settings |
|
1161 |
## |
|
1162 |
|
|
1163 |
# Dictionary can be used by some plugins to store key=value lists, such as |
|
1164 |
# quota, expire and acl plugins. The dictionary can be used either directly or |
|
1165 |
# though a dictionary server. The following dict block maps dictionary names to |
|
1166 |
# URIs when the server is used. These can then be referenced using URIs in |
|
1167 |
# format "proxy::<name>". |
|
1168 |
|
|
1169 |
dict { |
|
1170 |
#quota = mysql:/etc/dovecot-dict-quota.conf |
|
1171 |
#expire = db:/var/lib/dovecot/expire.db |
|
1172 |
} |
|
1173 |
|
|
1174 |
# Path to Berkeley DB's configuration file. See doc/dovecot-db-example.conf |
|
1175 |
#dict_db_config = |
|
1176 |
|
|
1177 |
## |
|
1178 |
## Plugin settings |
|
1179 |
## |
|
1180 |
|
|
1181 |
plugin { |
|
1182 |
# Here you can give some extra environment variables to mail processes. |
|
1183 |
# This is mostly meant for passing parameters to plugins. %variable |
|
1184 |
# expansion is done for all values. |
|
1185 |
|
|
1186 |
# Quota plugin. Multiple backends are supported: |
|
1187 |
# dirsize: Find and sum all the files found from mail directory. |
|
1188 |
# Extremely SLOW with Maildir. It'll eat your CPU and disk I/O. |
|
1189 |
# dict: Keep quota stored in dictionary (eg. SQL) |
|
1190 |
# maildir: Maildir++ quota |
|
1191 |
# fs: Read-only support for filesystem quota |
|
1192 |
# |
|
1193 |
# Quota limits are set using "quota_rule" parameters, either in here or in |
|
1194 |
# userdb. It's also possible to give mailbox-specific limits, for example: |
|
1195 |
# quota_rule = *:storage=1048576 |
|
1196 |
# quota_rule2 = Trash:storage=102400 |
|
1197 |
# User has now 1GB quota, but when saving to Trash mailbox the user gets |
|
1198 |
# additional 100MB. |
|
1199 |
# |
|
1200 |
# Multiple quota roots are also possible, for example: |
|
1201 |
# quota = dict:user::proxy::quota |
|
1202 |
# quota2 = dict:domain:%d:proxy::quota_domain |
|
1203 |
# quota_rule = *:storage=102400 |
|
1204 |
# quota2_rule = *:storage=1048576 |
|
1205 |
# Gives each user their own 100MB quota and one shared 1GB quota within |
|
1206 |
# the domain. |
|
1207 |
# |
|
1208 |
# You can execute a given command when user exceeds a specified quota limit. |
|
1209 |
# Each quota root has separate limits. Only the command for the first |
|
1210 |
# exceeded limit is excecuted, so put the highest limit first. |
|
1211 |
# Note that % needs to be escaped as %%, otherwise "% " expands to empty. |
|
1212 |
# quota_warning = storage=95%% /usr/local/bin/quota-warning.sh 95 |
|
1213 |
# quota_warning2 = storage=80%% /usr/local/bin/quota-warning.sh 80 |
|
1214 |
#quota = maildir |
|
1215 |
quota = maildir |
|
1216 |
|
|
1217 |
# ACL plugin. vfile backend reads ACLs from "dovecot-acl" file from maildir |
|
1218 |
# directory. You can also optionally give a global ACL directory path where |
|
1219 |
# ACLs are applied to all users' mailboxes. The global ACL directory contains |
|
1220 |
# one file for each mailbox, eg. INBOX or sub.mailbox. cache_secs parameter |
|
1221 |
# specifies how many seconds to wait between stat()ing dovecot-acl file |
|
1222 |
# to see if it changed. |
|
1223 |
#acl = vfile:/etc/dovecot-acls:cache_secs=300 |
|
1224 |
|
|
1225 |
# To let users LIST mailboxes shared by other users, Dovecot needs a |
|
1226 |
# shared mailbox dictionary. For example: |
|
1227 |
#acl_shared_dict = file:/var/lib/dovecot/shared-mailboxes |
|
1228 |
|
|
1229 |
# Convert plugin. If set, specifies the source storage path which is |
|
1230 |
# converted to destination storage (mail_location) when the user logs in. |
|
1231 |
# The existing mail directory is renamed to <dir>-converted. |
|
1232 |
#convert_mail = mbox:%h/mail |
|
1233 |
# Skip mailboxes which we can't open successfully instead of aborting. |
|
1234 |
#convert_skip_broken_mailboxes = no |
|
1235 |
# Skip directories beginning with '.' |
|
1236 |
#convert_skip_dotdirs = no |
|
1237 |
# If source storage has mailbox names with destination storage's hierarchy |
|
1238 |
# separators, replace them with this character. |
|
1239 |
#convert_alt_hierarchy_char = _ |
|
1240 |
|
|
1241 |
# Trash plugin. When saving a message would make user go over quota, this |
|
1242 |
# plugin automatically deletes the oldest mails from configured mailboxes |
|
1243 |
# until the message can be saved within quota limits. The configuration file |
|
1244 |
# is a text file where each line is in format: <priority> <mailbox name> |
|
1245 |
# Mails are first deleted in lowest -> highest priority number order |
|
1246 |
#trash = /etc/dovecot-trash.conf |
|
1247 |
|
|
1248 |
# Expire plugin. Mails are expunged from mailboxes after being there the |
|
1249 |
# configurable time. The first expiration date for each mailbox is stored in |
|
1250 |
# a dictionary so it can be quickly determined which mailboxes contain |
|
1251 |
# expired mails. The actual expunging is done in a nightly cronjob, which |
|
1252 |
# you must set up: |
|
1253 |
# dovecot --exec-mail ext /usr/lib/dovecot/expire-tool |
|
1254 |
#expire = Trash 7 Spam 30 |
|
1255 |
#expire_dict = proxy::expire |
|
1256 |
|
|
1257 |
# Lazy expunge plugin. Currently works only with maildirs. When a user |
|
1258 |
# expunges mails, the mails are moved to a mailbox in another namespace |
|
1259 |
# (1st). When a mailbox is deleted, the mailbox is moved to another namespace |
|
1260 |
# (2nd) as well. Also if the deleted mailbox had any expunged messages, |
|
1261 |
# they're moved to a 3rd namespace. The mails won't be counted in quota, |
|
1262 |
# and they're not deleted automatically (use a cronjob or something). |
|
1263 |
#lazy_expunge = .EXPUNGED/ .DELETED/ .DELETED/.EXPUNGED/ |
|
1264 |
|
|
1265 |
# Events to log. Also available: flag_change append |
|
1266 |
#mail_log_events = delete undelete expunge copy mailbox_delete mailbox_rename |
|
1267 |
# Group events within a transaction to one line. |
|
1268 |
#mail_log_group_events = no |
|
1269 |
# Available fields: uid, box, msgid, from, subject, size, vsize, flags |
|
1270 |
# size and vsize are available only for expunge and copy events. |
|
1271 |
#mail_log_fields = uid box msgid size |
|
1272 |
|
|
1273 |
# Sieve plugin (http://wiki.dovecot.org/LDA/Sieve) and ManageSieve service |
|
1274 |
# |
|
1275 |
# Location of the active script. When ManageSieve is used this is actually |
|
1276 |
# a symlink pointing to the active script in the sieve storage directory. |
|
1277 |
sieve=~/.dovecot.sieve |
|
1278 |
# |
|
1279 |
# The path to the directory where the personal Sieve scripts are stored. For |
|
1280 |
# ManageSieve this is where the uploaded scripts are stored. |
|
1281 |
sieve_dir=~/sieve |
|
1282 |
} |
|
1283 |
|
|
1284 |
# Config files can also be included. deliver doesn't support them currently. |
|
1285 |
#!include /etc/dovecot/conf.d/*.conf |
|
1286 |
# Optional configurations, don't give an error if it's not found: |
|
1287 |
#!include_try /etc/dovecot/extra.conf |